Vredevoogd Heating & Cooling technicians routinely assist our customers to figure out when it’s time to upgrade their Heating or Cooling system. Naturally, repairs are part of routine maintenance over the years. However, new models can save homeowners in a big way on energy expenses with their energy-efficient makeup. When you are ready to get a new system, we will do a careful check of your energy needs so that you can select the ideal system for your home’s needs. The wrong HVAC system for your home is a 15 year mistake that no one should have to afford. We install the right system for your home. Moreover, we offer guarantees that you won’t find just anywhere else. If your new installation isn’t right for your home, we’ll remove it free of charge at any time within that first year and refund 100% of your money. Our customers are burdened with no risks. We take on the risk because we are that sure of our expertise. We back our work with the strongest warranties in the field. In fact, we offer a wide array of warranties to provide you with the peace of mind you deserve as a valued Vredevoogd Heating & Cooling Grand Rapids MI customer.
Heat pumps that wring heat from outdoor air (and reverse the process in summer to act as an air conditioner) are inexpensive to install as an alternative to a cooling-only air-conditioning system. That makes them the preferred way to heat in the South and Southwest, where winters are typically short and mild. Heat pumps that wring heat from the ground are much more expensive to install, but they are suitable for cold climates because they can maintain their operating efficiency. Other inexpensive electric-heat options include strip heaters, which are installed in the ductwork of central air conditioning, and permanently installed baseboard units in each room. But before you consider any type of electric central heating in colder regions, keep in mind that electricity rates are much higher than those for natural gas and are likely to remain that way for the foreseeable future. You can get rate information for various fuels from local utilities and suppliers.
An electric furnace provides warmth by moving air over and through a series of coils. Ductwork and vents then distribute that air to the individual rooms in your home. Repair costs will depend on both the brand and the exact nature of the problem, but tend to be lower than some of the options above. That's because the units are small, and issues tend to be contained within the heating elements themselves. Expect to spend less than $300 on your electric furnace repair, depending on the exact problem.
Appointment was scheduled between 8am and 11 am, technician called and said that he will at 11 am, technician arrived at 11:23am. The request for service was regarding Furnace Maintenance, more specifically fan won't stop turning after heater has stopped after reaching desired temperature. Service was provide by Sam Singh from WesternAir Mechanical Heating & Air Conditioning. The mechanic opened the side panels of the heater+ac unit and concluded that the unit is too old for maintenance, as in it is not worth it, even though I have already payed $94.19 through Amazon.com. The mechanic spend close to one hour explaining how my heater+ac unit is too old for any updates and that it should just be replaced. I didn't receive any of the services that are included in the Furnace Maintenance package listed on Amazon.com. https://www.amazon.com/gp/product/B015JRGSQI/ref=od_aui_detailpages00?ie=UTF8&psc=1 I was ripped off my this company and I would very much like my money to be returned to me. Opening and closing the panels of my unit doesn't cost more than $2, I can do that by myself.
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.
Professionally installed air filtration systems in Federal Way, WA are the best way to ensure that your home has excellent indoor air quality. Let us help you breathe better air in your home. We offer a number of different air filtration systems from leading manufacturers in the industry, and we’d be happy to help you find one that meets your needs.
A whole–house air conditioning system in Federal Way, WA is by no means a luxury, but a necessity. At Bob’s Heating & Air Conditioning, our Federal Way air conditioning system specialists work with customers to ensure that their homes are comfortable all summer long. There is simply no other way to ensure that you and your family are cool during the summer than by having your cooling system service completed by a professional Federal Way air conditioning technician.
I'd had them come out before and called because my thermostat wasn't getting power. They said they don't service townhomes. I said that must be a new policy because they've been out before and she said they've had it for awhile. I tried to ask why they don't service townhomes and she said they don't service attached homes or commercial properties. I said that my home isn't commercial and it doesn't really answer my question, but I guess I'll go elsewhere. I couldn't find this policy on their website and I can't really understand why a townhome furnace would be different than an unattached home. When they came out before I seem to remember they did a good job, so it's too bad they have odd policies now.
As a Factory Authorized Dealer, Air Blue Heating and Cooling Inc. adheres to recommended service procedures, and if replacement parts are necessary, we rely on genuine factory authorized parts to restore original sound levels, efficiency ratings, and durability.  With over thirty years of industry experience, we’ve seen the consequences of neglected upkeep and the rewards of timely inspection from our skilled technicians.  Through seasonal cleaning, adjustment, and troubleshooting, we optimize all components, combat wear and tear, and head off potential difficulties.  The result is far fewer repair needs, lengthened service life, lower sound levels, superior air quality, safe operation, minimized operational costs, enhanced heating capacity, and greater value from your investment.  We also fulfill warranty requirements.  There are no drawbacks.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.
2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
While repair is often the preferred choice, problems like a consistent repeating complication or extra-costly furnace repair parts might start leading you in a different direction. Remember that repair is only the preferred option when the cost of seeking it makes sense! If you’re shelling out for repair every single year, then it might be time to talk to your heating contractor about furnace replacement.
Sky Heating & Air Conditioning provides a wide range of quality HVAC services to homeowners across Portland and The Dalles.  By bringing together skilled technicians and premier products, we deliver superior value for your investment.  We utilize tried and true strategies to enhance efficiency, comfort, and convenience throughout your home.  For heating and air conditioning installation, repair, and regular maintenance, no one takes better care of you than Sky Heating & Air Conditioning.  And we’re always here!  Count on us 24 hours a day, 7 days a week, to protect your safety, comfort, and best interests.
When winter sets in across Littleton, Lakewood, Centennial, Highlands Ranch & Englewood, CO, keeping a warm and comfortable home becomes a priority.  An efficient, safe, and reliable heating system is crucial.  You can count on Steel T Heating & Air Conditioning to keep costs down and rewards high, protecting your ongoing satisfaction with skilled installation, system replacement, seasonal maintenance, and heating repair.  As a Carrier Factory Authorized Dealer, we remain at the forefront of temperature control, specializing in effective heating service procedures and a wide range of the most technologically advanced equipment on the market.  Let us improve the quality of your comfort, enhance energy efficiency, and put precision control over your indoor environment at your fingertips. Contact us today for heating service in Littleton, Lakewood, Centennial, Highlands Ranch & Englewood, CO. Our NATE-certified technicians are always on call to provide Emergency Service, 24 hours a day, 7 days a week, and every project is handled quickly, accurately, and with unfailing professionalism.

2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
Ultimately, the cost to repair your furnace depends on a wide range of variables. From the brand of the units to the damaged or broken parts, you need a reliable and trusted professional who can evaluate the issue and recommend next steps. If you're unsure whether to repair or replace your furnace, or even where to begin, connect with a local furnace repair professional who can make sure that your home heats well both now and in the future.
Summers in Portland and The Dalles can be the absolute best time of year or pure torture.  Your cooling system makes the difference. Take advantage of perfectly maintained temperatures, superior dehumidification, unprecedented energy efficiency, and outstanding reliability with quality air conditioning products and services from Sky Heating & Air Conditioning.  We protect the enjoyment of your home with precise installation, system replacement, seasonal maintenance, and prompt repair.  Our skilled AC technicians are always on call 24 hours a day, 7 days a week, providing Emergency Service and protecting the value of your investment.  Every project is answered with a dedication to customer satisfaction that has earned us an A+ rating from the Better Business Bureau. Contact Sky Heating & Air Conditioning for air conditioning service in The Dalles and Portland, OR.  
Keeping too many heat registers closed can cause heat to build up in your furnace, forcing air out of duct leaks and requiring the blowers to compensate for the added pressure. Essentially, blocking heating vents causes your furnace to work harder and longer than it is intended to work. Further, it forces air pressure to build up in your air ducts, which may both cause and worsens airflow leaks — particularly at joints and seams. Pros recommend keeping at least 80 percent of your heating registers open to prevent unnecessary air from building up in your furnace.

Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.
Thank you, thank you, thank you for sharing your knowledge. I just replaced our shower cartridge and our leak is FIXED!!!!!!! Your instructional was clear and concise. I did purchase 2 cartridges first, because I did not know the type it was and could not pull it out without the plastic cover it comes with. Fortunately, it was one of the two. By the way I'm a 63 year old woman. If I can do it, anyone with internet and a little patience and an hour can do it.....
Call us today at (302) 200-4266 today to schedule a service heating system repair, replacement, installation, or tune-up services with our capable team! our team! We offer honest, upfront pricing in writing and industry leading warranties on parts and service. Find your local Horizon today to schedule heating system repair, replacement, installation, or tune-up services with our capable team!
For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.
We offer a wide range of air conditioning services in Federal Way, WA, from the installation of new systems from scratch to the replacement of old models that have seen better days. We can also make sure that your air conditioner is routinely cleaned and inspected with our routine maintenance. As always, our air conditioning technicians are available to repair your AC at a moment’s notice. Call us today for professional air conditioning service.

You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.


We are so happy we selected Clarence with CAL Property Care to repair our furnace. He was very easy to schedule an appointment with and actually came out on a Saturday to figure out what the issue was. Clarence had to order a part to complete the repair, but he promptly updated us with the progress every step of the way. Clarence really went above and beyond and I can't say enough for his friendly attitude and quality of work! Thanks again Clarence!

Let us take care of your water heater replacement in Federal Way, WA so that the job is done correctly the first time. We can make sure that your home has exactly what it needs for bountiful hot water. We offer a number of different makes and models to replace your old one, and we can ensure that it integrates seamlessly with the rest of your plumbing. Call Bob’s Heating & Air Conditioning today.
Drilon and Jeremy came out to the house for snaking the sewage line and performing an AC tune up. They were very informative, kind, respectful and professional. Drilon went above and beyond by giving me a whole walk through on our furnace, AC unit and water heater and giving suggestions and prioritizing what he thought would be the most important and safe for our new house right now. They were not pushy with their sales tactics and I will definitely be using them when we are ready to replace our features.
As a Carrier Factory Authorized Dealer, Edwards Heating & Air meets strict requirements for business practices, such as proper licenses, insurance and liability coverage, and customer service.  Our technicians participate in continued factory training, keeping current with advancements in techniques and technology, and adhere to strict installation and maintenance procedures.  Our sales team is educated in leading-edge Carrier products, ensuring accurate recommendations for cost-effective, highly efficient, and reliable solutions to your specific circumstances.  We specialize in heating, cooling, and air quality systems that are widely regarded as the world’s best.  Leading the industry in design and engineering, Carrier products offer unprecedented convenience, economy, and luxury.  These systems don’t just regulate temperature.  They improve your everyday life.

Two nights ago our smoke alarm went off during the night...after a frantic search through the house we traced the source of the smoke to the furnace.  After reading reviews about Affordable Furnace Repair we decided to give them a try...and we are SO GLAD WE DID!  Within 10 minutes of leaving a message I received a call back and was scheduled the next day.  The source of the problem was immediately identified and promptly fixed....a previous repair had messed up some wiring as well which was also fixed and now we are so glad to be back to 100%.  Can't say enough about the professionalism, responsiveness and service.  Highly recommend.
As touched on by their name, heat pumps function by transferring heat energy indoors during the winter and outdoors from your home during the summer. They're often attached to air conditioning units, using the surrounding air to transfer energy. However, geothermal heat pumps and water source heat pumps are also available. The cost to repair a heat pump, again, depends on the specific problem. Replacing a faulty thermostat may cost up to $300 including labor, while a worn or damaged defrost control board can set you back up to $600. For more details on your potential repair costs using this heating source, visit our heat pump repair cost guide.
At Horizon Services, we strive to go above and beyond for every one of our clients. We offer honest, upfront pricing in writing for every service we provide, as well as flexible scheduling to suit your needs, industry leading warranties, and a 100% customer satisfaction guarantee. When you call on us for heating services, our technicians will arrive on-time, every time. If we're even one minute later than the provided window of time, you don't pay. We understand that dealing with a broken or malfunctioning heating system can be incredibly frustrating. Let us turn your stressful situation into a thing of the past!
The flame sensor safeguards your furnace against the unsafe burning of fuel, and a dirty flame sensor may cause your furnace to function improperly. Typically, the flame sensor comes in the form of a rod that can be found near the back of the furnace, right in the path of the burner. To clean the sensor, turn off power to the furnace at the breaker box. Then, if possible, remove the sensor from the furnace. Scrub the sensor gently to remove dust and other residues. Finally, reattach the sensor and resume power to the furnace.

My furnace thermostat stopped working, and when I called Dehlia answered the phone and set up an appointment. They charged less for a diagnostic call than larger companies. They are actively licensed, bonded and insured. Verne arrived 2 days later, explained what was broken in my 17 year old furnace and gave me an estimate and time of replacement for a new furnace. Dehlia confirmed via email and phone, and Don and Zack showed up as promised on time a week later and replaced my Bryant 90i furnace with a new Rheem 96% efficient 2 stage Variable speed 85,000btu gas furnace Model #R96VA0852521 and provided me with the paperwork warranty and removed the old one. Cost was $5,394.90 including tax. I gave up on trying to get 2 more estimates because every furnace company wants $125 to $200 to come out to do a diagnostic and this company wanted $75 to come out to look at it although admittedly they just took a look at it and said it was broken and repair would be $2 to $3k and should just get a new  one (this fee was waived when I agreed to buy a new furnace from them). They also said it was possible I could find cheaper installation elsewhere, but I was freezing in December and I just wanted heat and other companies were 2 to 3 weeks out for an appointment.  They were pleasant to chat with as they worked and Don updated a convoluted furnace exhaust piping system. They accept cash and check after a job is finished with no deposit up front and are clear that 3% is added if you pay via credit card.  Overall I am happy with my new furnace although I sure wish I could've replaced it myself to save some money.

They did an outstanding work when you long time ago that our old furnace needed to be replaced. We contacted The Right Choice heating and air in one of the wraps came to our house give us a really good price for a new Trane furnace. The next day they arrived on time and finish the jobs within few hours we cleaned after themselves and made sure to ask us if we understand how to operate our new system. I will definitely recommend to use the Right choice heating and air
Adam V. from Swan Plumbing & Heating of Denver, CO came out and tuned up our furnace and A/C units. He was courteous prompt and professional, but beyond that went out of his way to give us recommendations on things we can do to get the most life and performance out of our existing equipment. When we are ready for upgrades and additional services, Swan will be our first (and only) call.
Rheem manufactures and markets gas central furnaces that are available in single and multistage configurations, with some models capable of an AFUE rating of more than 90 percent. Some units meet Energy Star requirements. The average price of a Rheem central gas furnace is about $2,300 and Rheems are sold through their dealer network. Rheem products are made by the same manufacturer as Ruud.
Efficient operation is a function of regular heating system maintenance. When a heating system malfunctions, any one of its three components – heat/cold source, distribution system, or the thermostat  – can be causing the problem. Our technicians can easily detect an impending issue before you have to replace a heating unit or spend a lot of money on parts and labor.
I highly recommend affordable furnace repair. Don and his helper were excellent and they always go above and beyond to make sure my furnace is in the best condition.  He gave me good tips and explained how the furnace works. I trust this company and am glad to have a company to take care of my furnace needs. This was my second time using Affordable Furnace Repair and will continue to use them in the future.
With certified, professional technicians covering the entire Twin Cities area, we’ve served over 475,000 customers. Ready for emergency repairs, Standard Heating has a fleet of technicians and service vehicles, with over 30 vehicles in the field on most days. For emergency service, call us immediately so that we can return your home to the comfort level you expect. We repair and service all brands of heating and cooling equipment including:
Walter was stupendous! He installed a new high-efficiency central air and furnace in my house. His master craftsmanship (artistry) and customer service are in a class of their own. From removing the old unit to all of the finishing touches, testing and review of operating the system, every detail was done in excess of what I could have imagine and I'm a Building Inspector. It was a very pleasant experience for me with only good surprises.
As you decide, insist that the contractor select models in a range of efficiencies and calculate the annual estimated operating cost of each model you're considering, rather than simply estimating it. The contractor can complete those calculations by plugging information on each unit's AFUE and electrical consumption, local utility rates, and characteristics of your home into one of several computer programs designed to easily calculate estimates. Make sure that the quotes also include the cost of any changes to venting required by any appliances in the home.

If you suspect that your furnace is no longer working as it should, then don’t keep that information to yourself. At Bob’s Heating & Air Conditioning, our heating repair specialists take pride in our ability to solve problems, and that includes comprehensive heating repair service in Federal Way, WA. If there is a problem with your furnace, we can provide a solution fast.
Thinking about a new water heater? Is yours ready to retire, or are you moving into a new home that doesn’t yet have one? When you call on Bob’s Heating & Air Conditioning, our Federal Way water heater installation technicians can make certain that the installation of your water heater goes according to plan. Our water heater specialists can help find a model that works for your budget.

“Walter Zainey started the Greenwood Furnace Co. in the Greenwood neighborhood of Seattle in 1918 and quickly built a reputation for providing quality products and services. For years we believed Greenwood began in 1921 but only recently, May of 2017, Walter’s granddaughter shared a newspaper ad from 1968 showing that Greenwood was actually founded in 1918! When your company goes back 100 years you are bound to have mixed messages about the history but we now have an accurate founding date and founder. Thank you to the Zainey family and especially Jacklyn for taking the time to share the story with us. I am sure Walter Zainey would be proud the heritage he created is still living on.
Zach came early, which I very much appreciated, and got the job done quickly. He was unfailingly polite and took care with putting on the booties and keeping my carpet clean. He managed to get the sprinkler system turned off even though I was quite uninformed about it and could help very little beyond pointing to where things were. I am always happy to have Brothers people come out to do my plumbing, heating, & electric services.
Partly to avoid that possibility, the furnaces in most homes are larger than necessary. Initial cost is only one of the drawbacks of that strategy. A furnace that's too large will cycle on and off more frequently. That puts more wear on its components, wastes energy, and might cause the temperature to vary uncomfortably. Also, a larger replacement furnace might require larger ducts. Without the right size ducts, airflow can be noisy.
Edwards Heating & Air continues to look for new ways to improve service.  We hire only NATE-certified, extensively experienced, and dedicated professionals.  We offer a wide range of products, from ductless options to heat pumps, furnaces, air conditioners, and air quality systems, guaranteed to answer the most challenging comfort demands.  To maintain your equipment in peak condition, promoting year after year of uninterrupted performance, we offer preventative service plans that are affordable, convenient, and effective.  If you are ever confronted with a malfunction, the team from Edwards Heating & Air is always available, 24 hours a day, 7 days a week, to provide the skilled assistance you need. Through our relationship with Wells Fargo Financial National Bank, we offer flexible financing options with approved credit to facilitate your investment into superior quality heating and cooling.  Our ongoing dedication to your complete satisfaction is evidenced by our complaint-free, A+ rating by the Better Business Bureau.  At Edwards Heating & Air, we do things right, every time.

If I could give them 10 stars I would. Don is extremely knowledgeable but more importantly honest. PSE had done a free diagnosis and told me I would need a new induction motor for around $850 or possibly a new furnace. PSE doesn't do the repairs so I found Affordable furnace on yelp. Don showed me where the noise was coming from and that we didn't need the other repair. He performed some routine maintenance and enlightened me on much better furnace filters. He said we will probably need a new furnace in a couple years but given the fact we've lived here 18 years and it was here before we got here I think we're doing pretty good. When it is time for a new furnace there's only one company we will be calling. Thanks Affordable Furnace!
Ashworth Heating & Cooling provides an affordable and reliable source of heating, cooling, air quality, and refrigeration services.  Specializing in installation, equipment updates, and maintenance repair, for both residential and commercial application, we ensure cost-effective solutions to every type of challenge.  Our goal is to simplify your life, minimize disruption, and optimize the performance of your essential systems.  When you contact Ashworth Heating & Cooling, we make it convenient to get the information, recommendations, and assistance you need, and deliver rewarding results in Hurricane, Huntington, Charleston, South Charleston, St. Albans, Dunbar & Milton, WV and all of the Tri-Country Area.
You'll find we take our job seriously and value highly the trust that is placed in us. To understand why we go so far beyond what others do by investing in the extra training and equipment we believe necessary to protect your home and family properly, take a moment to view our short 30 second video that best explains "why we do it"...and "why it matters."
Sometimes a heating and air conditioning system just needs to be repaired rather than completely replaced. You may need air conditioning repair services if there is leaking around the outside unit, the air coming into the house isn't hot or cool enough, the unit is short-cycling or constantly turning on and off, using the system is consistently resulting in higher-than-normal energy bills, or if there is excessive noise during startup and operation.
In addition to our gas and electric furnace installation, our Federal Way furnace technicians also make certain that your existing furnace works well for years to come with our furnace repair and maintenance services. Whether your furnace has broken down and no longer functions effectively, or you want to stave off problems by having it routinely maintained, we can help.
Keeping too many heat registers closed can cause heat to build up in your furnace, forcing air out of duct leaks and requiring the blowers to compensate for the added pressure. Essentially, blocking heating vents causes your furnace to work harder and longer than it is intended to work. Further, it forces air pressure to build up in your air ducts, which may both cause and worsens airflow leaks — particularly at joints and seams. Pros recommend keeping at least 80 percent of your heating registers open to prevent unnecessary air from building up in your furnace.

Our goal is to make you more comfortable in your home. When your furnace, central air conditioner, heat pump or boiler stops working and you need service, call the professionals at BGE HOME. Heating and cooling system breakdowns occur at the most inconvenient times, so rely on our certified, skilled technicians to make the repair quickly and correctly the first time.


As you decide, insist that the contractor select models in a range of efficiencies and calculate the annual estimated operating cost of each model you're considering, rather than simply estimating it. The contractor can complete those calculations by plugging information on each unit's AFUE and electrical consumption, local utility rates, and characteristics of your home into one of several computer programs designed to easily calculate estimates. Make sure that the quotes also include the cost of any changes to venting required by any appliances in the home.
Customer has a 3 year old American Standard gas furnace, she said that her furnace and thermostat were fried and not working. She had an electrician come by and inspect it, but he wasn't able to do anything. Upon investigation, I found that the thermostat has failed due to a power surge that hit the home. I also found that the fuse on the control board was blown and the contactor at the condenser was fried along with wiring. I replaced thermostat, contactor, and fuse/wiring and tested all modes of operation. All components are within manufacturers specifications and system fully operational. Recommend annual maintenance and power surge protector for either home or equipment.
James Heating & A/C, Inc offers furnace service appointments that help keep your furnace in tip-top shape and operating efficiently for you all winter long. Whether that’s finding small issues before they become big problems, identifying potential safety hazards or making sure you’re maintaining your manufacturer’s warranty, our experts have you covered. Our trained technicians complete furnace service with care, inspecting a number of components in and around your furnace. In fact, our multi-point inspection can help make sure your system runs smoothly throughout the winter.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
×