If you have an older furnace with a standing pilot light, it’s possible that the pilot light has been extinguished. First, confirm that the light is out. Then, turn the gas valve to the off position and wait five minutes. If there is a reset button on your furnace, turn the valve to the pilot position and hold a flame to the dedicated pilot opening while pushing the button for about 30 seconds. (If the pilot doesn’t light on the first attempt, wait a few minutes and repeat the procedure, this time depressing the reset button for 45-60 seconds.) Once the pilot is lit, turn the gas valve back to the on position. If the pilot light won’t stay lit, it’s possible that there is an issue with the thermocouple or ignition system. Call an HVAC professional for assistance.

Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.


The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
The motor belt should be firm, giving no more than ½ inch when pressed. It should also be free of cracks and damage. To remove the belt, you will need a wrench and a replacement belt. Loosen, do not remove, the motor bolts. You only need them loose enough to move the motor and slacken the belt. Remove the belt and inspect it, replacing it with a new one if necessary. Belt: $4.00 to $6.00.

Thank you Caleb Elliott for servicing our water heater. We are ready for winter! Caleb was very personable and did a thorough job servicing our water heater. We appreciate Reliable's commitment to service and keeping things running for us. Every service person we've had has been top notch. So glad we chose Reliable to take care of us. Continue reading...


I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
With more than 100 years in existence, Lennox has always delivered industry-leading innovation and technology while preserving stringent durability and reliability standards. The professionals at James Heating & A/C, Inc help bring those standards to Lexington so that you can always have total home comfort. If you’re in the market for a new HVAC system or even if you just have a question about what we offer, give us a call at 336-853-6070. We’d love to hear from you. 
There are many signs that can indicate the need for professional air conditioning repair service in Seattle, WA. You may notice that your air conditioner does not cool your home evenly, or that there is a spike in your air conditioning costs. Regardless of what tips you off, it is important that your air conditioning repair services are completed properly.
Mechanical air filters trap pollutants by filtering them out of the air as it passes through. Electronic air cleaners pull air in, give the pollutants in that air a static charge, and trap those pollutants on an oppositely charged surface. By working with a qualified professional you can rest assured that you have the right air filtration system in Seattle, WA.
There are a number of reasons that your water heater installation must be completed by a qualified party. First of all, it must be the right size so that it can handle your hot water needs. Plus, only a professional water heater installation in Seattle, WA can ensure that the system operates safely and effectively. Call today to discuss your water heater installation options.
Hi This is my 1st summer owning this house. My electric bill has been doubling for 3 months in a row..I have a Carrier 25HPA6 Performance Series 2 Stage Heat Pump...I recently went online and found instructions on how to clean the outdoor unit. I did so and it was not very dirty. I also have a generator that kicks on when I lose power which does not support the AC unit..We did lose power for a few days recently. I have 2 faults showing on the heat pump unit..one being 53 outdoor air sensor not reading or out of range 255 events and F 37 control fault, heater stuck on 13 events.It is set to cool and the fan to auto. I have never had a heat pump or central Air and am very green to this.The previous owners left no manuals.I have found one online but for installation only. PLease help?
If you need a furnace repaired or an air conditioner serviced, we'll send a local technician out to diagnose the specific problem and recommend solutions for you and your family. There will be a diagnostic fee for the visit, and any specific repairs will be an additional charge. If replacing your system is the best solution, the fee for the diagnosis will be credited toward the purchase and install of a new system.
Don and Zac came out and assessed the furnace and explained why it was now time to replace it. Don explained in detail what we should look for (the job is bigger than his preferred scope) and the kind of furnace he recommended. When I asked him for his bill, he said, "Call it an estimate. No charge." I thanked them profusely and paid them in cookies. Affordable Furnace is a great business whose expertise and integrity you can trust.
Of the various contractors and HVAC service companies, why should you choose AQS for air conditioning and furnace repair? Our company is a family-owned and operated business that has been in business since 1996. It goes without saying that we are extremely experienced in the installation and repair of heating and cooling units. We are proud of our A+ rating from the BBB, and we have received numerous Super Service Awards from Angie's List, both in recognition of the quality services we provide.
The flame sensor safeguards your furnace against the unsafe burning of fuel, and a dirty flame sensor may cause your furnace to function improperly. Typically, the flame sensor comes in the form of a rod that can be found near the back of the furnace, right in the path of the burner. To clean the sensor, turn off power to the furnace at the breaker box. Then, if possible, remove the sensor from the furnace. Scrub the sensor gently to remove dust and other residues. Finally, reattach the sensor and resume power to the furnace.
With more than 100 years in existence, Lennox has always delivered industry-leading innovation and technology while preserving stringent durability and reliability standards. The professionals at James Heating & A/C, Inc help bring those standards to Lexington so that you can always have total home comfort. If you’re in the market for a new HVAC system or even if you just have a question about what we offer, give us a call at 336-853-6070. We’d love to hear from you. 
As a Factory Authorized Dealer, Air Blue Heating and Cooling Inc. adheres to recommended service procedures, and if replacement parts are necessary, we rely on genuine factory authorized parts to restore original sound levels, efficiency ratings, and durability.  With over thirty years of industry experience, we’ve seen the consequences of neglected upkeep and the rewards of timely inspection from our skilled technicians.  Through seasonal cleaning, adjustment, and troubleshooting, we optimize all components, combat wear and tear, and head off potential difficulties.  The result is far fewer repair needs, lengthened service life, lower sound levels, superior air quality, safe operation, minimized operational costs, enhanced heating capacity, and greater value from your investment.  We also fulfill warranty requirements.  There are no drawbacks.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
Rheem manufactures and markets gas central furnaces that are available in single and multistage configurations, with some models capable of an AFUE rating of more than 90 percent. Some units meet Energy Star requirements. The average price of a Rheem central gas furnace is about $2,300 and Rheems are sold through their dealer network. Rheem products are made by the same manufacturer as Ruud.
Our technicians have experience repairing furnaces and will make sure your home is back to keeping your family cozy in no time. From training and certifications to our reputation for doing the job right time and time again, you can trust that James Heating & A/C, Inc’s furnace repair technicians will have your troubles taken care of and your furnace operating smoothly. Whether it’s emergency furnace repair or service you can schedule a little in advance, our team can give you peace of mind, knowing that your furnace is in good hands. Are you in need of a furnace repair? When performing a repair, it's important to hire professional HVAC contractors.
We are committed to providing you with services that are effective and efficient. We do the job right the first time, but more importantly, we won't charge our customer when we didn’t fix it the first time. For almost 30 years, we have been providing our customers with work from industry-certified technicians. Our team has the skill and knowledge to get the job done right the first time out!
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
This is probably the most common question we hear. To give an accurate price, we need to get a safety certified technician out to your home in a fully stocked truck to take a look at your particular situation. Our technician will give you a precise price with your options BEFORE any work begins. Each of our technicians are well trained, experienced, drug tested and background checked so that you can rest easy knowing your services will be performed in a timely and professional manner. If you need help paying for your services, we even offer financing with approved credit through Wells Fargo. Click here to learn more about our financing services.
×