There’s a common misconception that you can save money by shutting the vents (supply registers) in rooms that aren’t being utilized. Resist the urge to close too many, as doing so can actually increase the pressure in your furnace, making it work harder to heat your home. This can lead to failed blower motors, mold or mildew in your ductwork, damage to the compressor, a cracked heat exchanger, and other problems. What Does a Furnace Tune-Up Include?
Steel T Heating & Air Conditioning is uniquely qualified to recommend and install the industry’s most recognized heating and cooling systems, from central air conditioners and furnaces, to heat pumps, ductless units, and air quality accessories. We offer a range of innovative products to improve the health, comfort, and convenience of your everyday life. Plus, we’ll stand with you throughout the entire product life, offering skilled installation and replacement, seasonal maintenance, and 24 hour repair to maximize the return on your investment. Targeting cost-savings, energy efficiency, reliability, and safety, Steel T Heating & Air Conditioning is your single solution for temperature control. Contact us to day for heating and air conditioning services in Littleton, Lakewood, Centennial, Highlands Ranch & Englewood, CO.
When your gas furnace isn’t blowing hot air, the issue could be due to a faulty pilot light or broken ignitor. Remove the furnace cover panel and visually inspect whether you can see a flame from the pilot light. A natural gas furnace will be blue and yellow in color, and a propane furnace should have a bluish green flame with a yellow tip. If you can see a flame and it appears normal, the issue could be related to the furnace blower motor or other complex furnace parts. If the flame appears low or non-existent, it’s best to contact an experienced furnace repair company. Remember to never touch any open wires; contact a professional.

If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.


I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
Keeping too many heat registers closed can cause heat to build up in your furnace, forcing air out of duct leaks and requiring the blowers to compensate for the added pressure. Essentially, blocking heating vents causes your furnace to work harder and longer than it is intended to work. Further, it forces air pressure to build up in your air ducts, which may both cause and worsens airflow leaks — particularly at joints and seams. Pros recommend keeping at least 80 percent of your heating registers open to prevent unnecessary air from building up in your furnace.
If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
I was able to get an appointment easily and they arrived promptly.  They detected the problem and repaired it quickly.  A few days later, I encountered another problem and again, I was able to get an appointment easily and they arrived promptly.  They recommended some easy fixes and now everything is working well again.  I can recommend them without qualification.  The guys that came out to my house were great.
We install heating equipment from Lennox and can repair all major brands, including Carrier, Trane, York, Bryant, Rheem, and many more. We proudly offer same day service and next day installations. Dealing with a heating emergency? We've got you covered! Our team is prepared to assist you 24 hours a day, 7 days a week to ensure that your home remains comfortable and safe for you and your family members.
This makes heat pumps a highly energy efficient solution. At Bob’s Heating & Air Conditioning, our Federal Way heat pump specialists often recommend heat pumps because they allow our customers to use a single system year–round. As a highly energy efficient device, your heat pump may also save you money in the long term. Let us take care of your heat pump needs in Federal Way, WA, whether that’s installation or repair.
“Walter Zainey started the Greenwood Furnace Co. in the Greenwood neighborhood of Seattle in 1918 and quickly built a reputation for providing quality products and services. For years we believed Greenwood began in 1921 but only recently, May of 2017, Walter’s granddaughter shared a newspaper ad from 1968 showing that Greenwood was actually founded in 1918! When your company goes back 100 years you are bound to have mixed messages about the history but we now have an accurate founding date and founder. Thank you to the Zainey family and especially Jacklyn for taking the time to share the story with us. I am sure Walter Zainey would be proud the heritage he created is still living on.
Customer called requesting standard maintenance on their gas furnace and their tankless water system. System is running well, all components are within manufacturers specifications. No issues other than thermostat which home owner is aware of. Recommend annual maintenance Tankless Maint - Unit has been flushed and inspected. All operations normal at this time.
Customer has a 3 year old American Standard gas furnace, she said that her furnace and thermostat were fried and not working. She had an electrician come by and inspect it, but he wasn't able to do anything. Upon investigation, I found that the thermostat has failed due to a power surge that hit the home. I also found that the fuse on the control board was blown and the contactor at the condenser was fried along with wiring. I replaced thermostat, contactor, and fuse/wiring and tested all modes of operation. All components are within manufacturers specifications and system fully operational. Recommend annual maintenance and power surge protector for either home or equipment.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.

Denver furnace repair is very common in the winter. Our availability 7 days a week is a major advantage. That is the main reason as to why we are a popular furnace repair company. In general, furnaces tend not to start at all or are cracking out cold air instead of heat. Contact us, your Denver furnace repair company so that we can diagnose the problem and set you up with a preventative maintenance package. Click HERE to learn more about our furnace related services.
×