The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.


We are famous for being honest and committed with high quality and value to 100% customer satisfaction 7 days a week especially since furnace repair in Denver is popular. The company is generally proud to comment that “All our specialists are drug tested and background checked.” It is also rare and interesting to comment that the techs use shoe covers and floor mats to keep all homes the same way they found them. You won’t find an equal level of commitment that our technicians provide clients anywhere else.
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
Heating your home is an essential part of feeling comfortable while indoors and is also essential for health and safety during a chilly winter evening. When temperatures dip into the 20s and 30s, you need emergency heating repair in Houston. From general repairs like pumps, gas valves, heat exchangers, diverter valves, flow switches and fans, to total heating system replacements and installations, Abacus Plumbing can ensure your home is warm when it needs to be. Don’t be left out in the cold! Call Abacus Plumbing today for a quality, reliable heater repair company in the Houston area.

This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
The professionals here at Brothers Plumbing, Heating and Electric are well trained, experienced and seasoned experts. We have been the go-to plumbing, electrical and HVAC company in the area for over 35 years and we always come highly recommended by our many satisfied customers. We offer a 100% satisfaction guarantee, have an A+ Rating with the BBB, won the Thornton “People’s Choice Award” for 2016, drug test and background check all of our employees, email you a picture of the technician who will be providing the service before arrival and call once the service is complete to ensure 100% satisfaction. So what are you waiting for? With our competitive pricing, trained and experienced technicians, and well-rounded list of home services, we’re clearly the company to trust. Get in touch with us here at Brothers Plumbing, Heating and Electric to schedule your needed service today!
As a Carrier Factory Authorized Dealer, Edwards Heating & Air provides superior quality products and workmanship to home and business owners in Acworth and across Acworth, Alpharetta, Cummings, Cartersville, Kennesaw & Woodstock, GA.  Our NATE-certified technicians adhere to strict installation and service procedures, and are uniquely qualified to recommend the most cost-effective solutions to meet your exact needs and expectations.  Whether you are in the market for an HVAC system for new construction, a replacement unit, ductless options, heat pumps, or air conditioning, Edwards Heating & Air ensures a refreshingly cool and healthy home and work environment.  Through accurate sizing, precision installation, and conscientious maintenance, we help you enjoy maximum return from your investment and reliable operation, year after year.  For any cooling challenge you may face, the team from Edwards Heating & Air are your problem solvers, and we are always here when you need us, 24 hours a day, 7 days a week.
When winter sets in across Littleton, Lakewood, Centennial, Highlands Ranch & Englewood, CO, keeping a warm and comfortable home becomes a priority.  An efficient, safe, and reliable heating system is crucial.  You can count on Steel T Heating & Air Conditioning to keep costs down and rewards high, protecting your ongoing satisfaction with skilled installation, system replacement, seasonal maintenance, and heating repair.  As a Carrier Factory Authorized Dealer, we remain at the forefront of temperature control, specializing in effective heating service procedures and a wide range of the most technologically advanced equipment on the market.  Let us improve the quality of your comfort, enhance energy efficiency, and put precision control over your indoor environment at your fingertips. Contact us today for heating service in Littleton, Lakewood, Centennial, Highlands Ranch & Englewood, CO. Our NATE-certified technicians are always on call to provide Emergency Service, 24 hours a day, 7 days a week, and every project is handled quickly, accurately, and with unfailing professionalism.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
• If your furnace is inside the house, it may be located in an area that is magnifying the sound it makes – such as under a staircase. Often moving the furnace to another part of the house can reduce that noise. You may find that it’s in an area that was previously occupied by another older type of furnace, and you never heard those sounds from that one. Please keep in mind that modern furnaces are built differently – with multiple speeds and stages – which may create different sounds and require more airflow than your old ductwork has available. If the furnace doesn’t get enough air, it gets cranky.
Our company’s strength lies in our years of experience performing air conditioning and heating repair in Voorhees, Sewell, Haddonfield, and other towns in and around South Jersey. We also take pride in the high standard we set for the quality of our AC repair and work, and our unfaltering dedication to our customers located in Haddonfield, Sewell, and other parts of Jersey. For three generations we have kept these ideals at the forefront of our operations, allowing us to continue to be one of Southern New Jersey’s leading HVAC Contractors and air conditioner companies.
As a Carrier Factory Authorized Dealer, Edwards Heating & Air provides superior quality products and workmanship to home and business owners in Acworth and across Acworth, Alpharetta, Cummings, Cartersville, Kennesaw & Woodstock, GA.  Our NATE-certified technicians adhere to strict installation and service procedures, and are uniquely qualified to recommend the most cost-effective solutions to meet your exact needs and expectations.  Whether you are in the market for an HVAC system for new construction, a replacement unit, ductless options, heat pumps, or air conditioning, Edwards Heating & Air ensures a refreshingly cool and healthy home and work environment.  Through accurate sizing, precision installation, and conscientious maintenance, we help you enjoy maximum return from your investment and reliable operation, year after year.  For any cooling challenge you may face, the team from Edwards Heating & Air are your problem solvers, and we are always here when you need us, 24 hours a day, 7 days a week.
Sky Heating & Air Conditioning answers any comfort challenge with straightforward, satisfying solutions. We get rid of the need for labor-intensive renovation. We don’t tear down walls or ceilings, steal precious closet space for the installation of ductwork, or cause mess or damage. With the installation of a ductless HVAC system, we answer your temperature control requirements with wonderful simplicity.
I'd had them come out before and called because my thermostat wasn't getting power. They said they don't service townhomes. I said that must be a new policy because they've been out before and she said they've had it for awhile. I tried to ask why they don't service townhomes and she said they don't service attached homes or commercial properties. I said that my home isn't commercial and it doesn't really answer my question, but I guess I'll go elsewhere. I couldn't find this policy on their website and I can't really understand why a townhome furnace would be different than an unattached home. When they came out before I seem to remember they did a good job, so it's too bad they have odd policies now.
If you suspect that your furnace is no longer working as it should, then don’t keep that information to yourself. At Bob’s Heating & Air Conditioning, our heating repair specialists take pride in our ability to solve problems, and that includes comprehensive heating repair service in Federal Way, WA. If there is a problem with your furnace, we can provide a solution fast.

Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.
There are many signs that can indicate the need for professional air conditioning repair service in Seattle, WA. You may notice that your air conditioner does not cool your home evenly, or that there is a spike in your air conditioning costs. Regardless of what tips you off, it is important that your air conditioning repair services are completed properly.
Bryant manufactures and markets gas central furnaces that are available in single and multistage configurations, with some models capable of an AFUE rating of more than 90 percent. Bryant markets units that meet Energy Star requirements and makes others that it claims offer quiet operation. A new line of hybrid heat systems that uses gas and an electric heat pump was recently introduced. The average price of a Bryant central gas furnace is about $2,300 and Bryants are sold through their dealer network.
A pinging or popping sound coming from the duct work can come from thermal expansion—the ductwork expanding and contracting as it heats and cools.  Or, air blowing past a loose flap of metal can make the sound. Track along the duct runs, listening for the sound. If you locate it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
Ruud, Trane, and American Standard are among the more reliable natural gas furnace brands, whereas Goodman, Lennox, and Amana are among the less reliable brands. York, however, stands out as the least reliable brand and cannot be recommended by Consumer Reports at this time. That’s what we found based on the feedback of 21,618 subscribers, who reported on their experiences with gas furnaces installed between 2011 and 2016.
Professional air duct cleaning in Federal Way, WA is important because it ensures that your ductwork functions as it is supposed to. When dust and other debris accumulate inside your ducts, they can hinder airflow, which can raise your energy consumption and cause the cost of cooling to be much higher than should be the case. Let us keep your ducts in good working order.

There will always be an occasion for you to rely on a heating or air conditioning system. The major appliances make comfortable life possible, providing warmth on nippy days and cool air during humid summers. Whether or not you use them daily, however, your heating and air conditioning systems need to be maintained every now and then to ensure that they function properly.
Of the various contractors and HVAC service companies, why should you choose AQS for air conditioning and furnace repair? Our company is a family-owned and operated business that has been in business since 1996. It goes without saying that we are extremely experienced in the installation and repair of heating and cooling units. We are proud of our A+ rating from the BBB, and we have received numerous Super Service Awards from Angie's List, both in recognition of the quality services we provide.
I met the owner while looking at a new house, he was servicing the furnace. I asked for a card and explained that I live in a townhome, he said not a problem. Well I called a day or so late to schedule an appointment. That went smooth due to the season the schedule was 3-4 weeks out. I understand and wait patiently. Week the day before the scheduled service i got a reminder call, those are helpful. Well the gal on the phone calls back a few minutes later she called back and came up with a few excuses on why they can no longer come look at my furnace. They seemed pretty hollow to me and she took a fairly snippy attitude with me as well. Due to hire this went down and the fact that it took a month for them to say no can do, I will never ever pay a positive wire forward towards this company!
Your heating, cooling, and air quality systems are a significant investment, and are expected to answer high demand, day after day, year after year.  To enjoy the greatest benefit from your equipment, let the professionals from Edwards Heating & Air handle the essential upkeep.  Through conscientious, seasonal maintenance, we effectively restore operational sound and efficiency levels, improve air quality, eliminate the majority of repairs, and extend service life.  The key to safe and uninterrupted performance, lower overall costs, and superior temperature control is through proactive measures.  The NATE-certified technicians from Edwards Heating & Air complete a lengthy task list that is specifically targeted at the optimization of your system.  Not only will your HVAC system be ready and able to handle volatile weather conditions, but it will operate safely.  Comprehensive service from Edwards Heating & Air is your best protection against health concerns, property damage, system failure, and elevated cost of ownership.  Contact Edwards Heating & Air, and we'll set up a maintenance plan that is affordable, convenient, rewarding, and works perfectly for you.
Does your water heater make a loud or strange sound during operation? Are you sick and tired of unreasonably high energy bills? Are you out of hot water? Let us take a look at your water heater so that we can take care of any problems that may arise with its operation. Our water heater repair services in Federal Way, WA are thorough and comprehensive.
Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
Gas is currently the most common heating fuel and most new central-heating systems use gas. How efficiently a furnace converts gas into heating energy is reflected in its annual fuel-utilization-efficiency (AFUE) rating, which is measured as a percentage. The higher the number, the more heat the furnace can wring from each therm of gas. Since efficient furnaces generate fewer emissions, environmental considerations might also influence your decision.
When you need a new air conditioner installation, Seattle furnace repair, or want to schedule routine water heater maintenance, there is one company to call: Bob’s Heating & Air Conditioning. We have years of experience with heating, air conditioning and water heater services, and we can ensure that your home is comfortable throughout the entire year. Contact us today to schedule the high–quality HVAC and water heater services you deserve.
There are a number of reasons that your water heater installation must be completed by a qualified party. First of all, it must be the right size so that it can handle your hot water needs. Plus, only a professional water heater installation in Seattle, WA can ensure that the system operates safely and effectively. Call today to discuss your water heater installation options.
You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.
×