Fitting a furnace with an electrostatic filter, which uses an electrical charge to help trap particles, or a high-efficiency particulate-arresting (HEPA) filter can reduce the amount of dust blown through the heating system. That might help people with asthma or other chronic lung diseases, but there's little evidence that other people need such filtration.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
Geothermal Heating and Cooling systems are unmatched in every way. This green alternative to temperature control is three times more efficient than conventional systems. Recognized by the US Environmental Protection Agency as the most environmentally-friendly option available today, installation of a geothermal HVAC system translates into a 50% reduction in heating costs, 30% reduction in cooling costs, and a 65% potential savings on hot water costs.  Sky Heating & Air Conditioning is now the largest WaterFurnace geothermal contractor west of Iowa. Our team of experienced professionals offer conscientious and skilled start-to-finish installation and service.  We specialize in outstanding geothermal HVAC systems, adding value and enjoyment to your home through sustainable solutions to year round temperature control. Contact Sky Heating & Air Conditioning for geothermal heat pump installation in Portland.

You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.
Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
Misurelli Sorensen Heating & Air Conditioning, is a Wisconsin (WI) Heating, Cooling, Air Conditioning, Geothermal Heat Pump, Ductless Mini-Split, Boiler, Water Heater, Fireplace, and Furnace repair, service, replacement, and maintenance Company located in all of Metro Milwaukee. Misurelli Sorensen Heating & Air Conditioning employs only the best technician for air conditioner, furnace, and boiler repair as well as all air conditioner, furnace, and heat pump replacement in Kenosha WI, Somers WI, Racine WI, Pleasant Prairie WI, Sturtevant WI, Woodworth WI, Bristol WI, Benet Lake WI, Union Grove WI, Franksville WI, Caledonia WI, Salem WI, Kansasville WI, Trevor WI, Camp Lake WI, Silver Lake WI, Oak Creek WI, Wilmot WI, South Milwaukee WI, Franklin WI, New Munster WI, Bassett WI, Rochester WI, Twin Lakes WI, Waterford WI, Cudahy WI, Burlington WI, Greendale WI, Muskego WI, Milwaukee WI, Saint Francis WI, Powers Lake WI, Hales Corners WI. So when you ask to find "A good heating and air conditioning repair or service company near me," you've come to the right place. To set-up a repair service estimate or replacement estimate, call (262) 551-9121. Misurelli Sorensen Heating & Air Conditioning services all furnace, AC, humidifier, filter, thermostat and water heater brands including Carrier, Bryant, Payne, Trane, Lennox, Rheem, Ruud, Amana, Daikin, Mitsubishi, Fujitsu, Crown, Frigidaire, Gibson, Goodman, Lochinvar, Maytag, Weil McLain, A O Smith, Kohler, American Standard, GeoExcel, General, Aprilaire, Honeywell, White Rodgers, Dynamic and Skuttle.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.

Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
×