Seattle furnaces can run nine months of the year. Based on the average temperatures in our area, if you compared running your furnace to a car it would get the equivalent of 1.8 million miles over its expected lifespan of 15 years. Your heating system will work hard for you, but like your car, doing routine and regular maintenance will keep it running smoothly, avoid problems, and keep your warranty intact.
The national average for furnace replacement is between $1,800 and $2,500. The cost can range dramatically higher depending on the model of furnace you select, any repair work you require, your location and the cost of installation. Furnace installation costs can be more than the furnace itself due to the cost of doing business and the expertise needed to install the HVAC equipment. Installing a new furnace generally requires technical know-how and the proper tools and licensing. It’s best to hire a pro and budget for furnace installation rather than risk potentially unsafe DIY installation. This will ensure your home’s safety. Check to see if your HVAC contractor has the proper licensing to do the job. If you need duct repair or replacement, expect to pay more for your furnace installation costs. The price for duct repair could be an hourly rate ranging on average anywhere from $85 to $150 per hour, with additional costs for parts.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.
The flame sensor safeguards your furnace against the unsafe burning of fuel, and a dirty flame sensor may cause your furnace to function improperly. Typically, the flame sensor comes in the form of a rod that can be found near the back of the furnace, right in the path of the burner. To clean the sensor, turn off power to the furnace at the breaker box. Then, if possible, remove the sensor from the furnace. Scrub the sensor gently to remove dust and other residues. Finally, reattach the sensor and resume power to the furnace.
Ashworth Heating & Cooling provides an affordable and reliable source of heating, cooling, air quality, and refrigeration services. Specializing in installation, equipment updates, and maintenance repair, for both residential and commercial application, we ensure cost-effective solutions to every type of challenge. Our goal is to simplify your life, minimize disruption, and optimize the performance of your essential systems. When you contact Ashworth Heating & Cooling, we make it convenient to get the information, recommendations, and assistance you need, and deliver rewarding results in Hurricane, Huntington, Charleston, South Charleston, St. Albans, Dunbar & Milton, WV and all of the Tri-Country Area.
If you have an older furnace with a standing pilot light, it’s possible that the pilot light has been extinguished. First, confirm that the light is out. Then, turn the gas valve to the off position and wait five minutes. If there is a reset button on your furnace, turn the valve to the pilot position and hold a flame to the dedicated pilot opening while pushing the button for about 30 seconds. (If the pilot doesn’t light on the first attempt, wait a few minutes and repeat the procedure, this time depressing the reset button for 45-60 seconds.) Once the pilot is lit, turn the gas valve back to the on position. If the pilot light won’t stay lit, it’s possible that there is an issue with the thermocouple or ignition system. Call an HVAC professional for assistance.
The heating installation process must be completed by a professional heating technician. There is simply no other way to make sure that your furnace is correctly integrated into the home. We take care of every detail, from the gas piping for the furnace to the ducts placed behind walls and in ceilings. Give us a call today to find out more about our Federal Way heating installation service.
Customer called requesting standard maintenance on their gas furnace and their tankless water system. System is running well, all components are within manufacturers specifications. No issues other than thermostat which home owner is aware of. Recommend annual maintenance Tankless Maint - Unit has been flushed and inspected. All operations normal at this time.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
A pinging or popping sound coming from the duct work can come from thermal expansion—the ductwork expanding and contracting as it heats and cools. Or, air blowing past a loose flap of metal can make the sound. Track along the duct runs, listening for the sound. If you locate it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
Whether you are looking for gas furnace service or repair, quality installation of a furnace, heat pump or air conditioner, mini split ductless heat pumps, endless hot water from tankless water heaters, better air quality in your home or just a filter change or duct cleaning, Greenwood Heating is your best choice of Seattle heating contractors and cooling specialists.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
Effective Air provides Solutions For A Healthier Home in the Chicagolands North Shore. With a wide range of services, we simplify your life, protect your investment, and deliver straightforward solutions to everyday challenges. As a small, family owned business, we recognize the difficulty of keeping a comfortable, energy-efficient, and smoothly operating household. We respond with flexible appointment times, prompt arrival, swift completion, and organized job sites. For every project, we offer honest answers and knowledgeable recommendations, targeting your goals with skilled workmanship and quality products and materials.
“Walter Zainey started the Greenwood Furnace Co. in the Greenwood neighborhood of Seattle in 1918 and quickly built a reputation for providing quality products and services. For years we believed Greenwood began in 1921 but only recently, May of 2017, Walter’s granddaughter shared a newspaper ad from 1968 showing that Greenwood was actually founded in 1918! When your company goes back 100 years you are bound to have mixed messages about the history but we now have an accurate founding date and founder. Thank you to the Zainey family and especially Jacklyn for taking the time to share the story with us. I am sure Walter Zainey would be proud the heritage he created is still living on.
We also offer a great selection of electric furnaces in Seattle, WA. While natural gas does tend to cost less to purchase than electricity, today’s electric furnace models are so efficient that they can really close the price gasp. Call our Seattle furnace experts if you are interested in learning more about the benefits of heating your home with an electric furnace.
While there's nothing you can do to guarantee your air conditioner or furnace will never need repairs, there are ways to take better care of your system. Changing out the air filters every 3-6 months, making sure nothing is obstructing or interfering with the outside unit, and keeping all vents unblocked in well-used rooms will help keep your air conditioning and heating system operating efficiently.
When you work with Bob’s, we make sure your furnace is properly sized and installed for optimal performance. When it comes to furnace installation in Renton, WA, Bob’s is dedicated to excellence, which defines our service. We know that professional furnace installation is the best way to protect its performance quality. Call today for more details.
We offer a wide range of air conditioning services in Federal Way, WA, from the installation of new systems from scratch to the replacement of old models that have seen better days. We can also make sure that your air conditioner is routinely cleaned and inspected with our routine maintenance. As always, our air conditioning technicians are available to repair your AC at a moment’s notice. Call us today for professional air conditioning service.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.
This is probably the most common question we hear. To give an accurate price, we need to get a safety certified technician out to your home in a fully stocked truck to take a look at your particular situation. Our technician will give you a precise price with your options BEFORE any work begins. Each of our technicians are well trained, experienced, drug tested and background checked so that you can rest easy knowing your services will be performed in a timely and professional manner. If you need help paying for your services, we even offer financing with approved credit through Wells Fargo. Click here to learn more about our financing services.