As your water heater operates it will incur some general wear and tear; there is no way to prevent this. With the help of a Seattle, WA water heater maintenance specialist, though, you can keep this wear and tear from developing into major headaches down the road. We’ll make sure that your water heater is in the great operating condition you deserve.
The flame sensor safeguards your furnace against the unsafe burning of fuel, and a dirty flame sensor may cause your furnace to function improperly. Typically, the flame sensor comes in the form of a rod that can be found near the back of the furnace, right in the path of the burner. To clean the sensor, turn off power to the furnace at the breaker box. Then, if possible, remove the sensor from the furnace. Scrub the sensor gently to remove dust and other residues. Finally, reattach the sensor and resume power to the furnace.

This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
When your furnace isn’t regularly serviced it can operate less efficiently. This increases your energy bills and also prevents your furnace from keeping your home as warm as you like. Keep your furnace properly maintained with regular service. The national average furnace service cost is between $60 and $80. Companies may offer tuneup specials that cover all the necessary testing, tightening, measuring and cleaning to keep your equipment running at top efficiency. If you have a newer system, furnace service costs may be covered by your warranty. Outside of warranty, a basic tuneup might start at $58 and a more advanced maintenance cleaning could be over $120. Here are some signs your furnace may need service:
Seattle furnaces can run nine months of the year. Based on the average temperatures in our area, if you compared running your furnace to a car it would get the equivalent of 1.8 million miles over its expected lifespan of 15 years. Your heating system will work hard for you, but like your car, doing routine and regular maintenance will keep it running smoothly, avoid problems, and keep your warranty intact.
Our new HVAC unit started to leak badly, so we set up an appointment for an on-site diagnosis. The two-man crew arrived in the agreed-upon window and was very experienced. They gave off the impression that they had seen just about everything before. They quickly found the source of the problem, fixed it, and explained in full what they were doing and why. They also offered up some helpful tips of what to look for and how to self-diagnose issues.
Zach came early, which I very much appreciated, and got the job done quickly. He was unfailingly polite and took care with putting on the booties and keeping my carpet clean. He managed to get the sprinkler system turned off even though I was quite uninformed about it and could help very little beyond pointing to where things were. I am always happy to have Brothers people come out to do my plumbing, heating, & electric services.
Attic Fan Installation Bathroom Fan Repair Ceiling Fan Installation Ceiling Fan Repair Electric Wall Heater Installation Electrical Panel Installation Electrical Panel Repair Electrical Panel Upgrade Electrical Wiring Installation Electrical Wiring Upgrade Exhaust Fan Installation Holiday Lighting Installation LED Interior Light Conversion Light Fixture Installation Light Fixture Repair Light Fixture Replacement Light Switch Installation Outlet Installation Outlet Repair Spa Wiring Installation

Turn off the gas supply valve, typically located by your gas meter on the gas inlet pipe. Turn off the gas by rotating the valve one quarter turn with an adjustable wrench. When the gas is off,  the valve’s oblong stem points perpendicular to the inlet pipe. Then call your gas utility or the fire department from a remote location. Do not return to your home until you know it is safe.

I highly recommend affordable furnace repair. Don and his helper were excellent and they always go above and beyond to make sure my furnace is in the best condition.  He gave me good tips and explained how the furnace works. I trust this company and am glad to have a company to take care of my furnace needs. This was my second time using Affordable Furnace Repair and will continue to use them in the future.


The flame sensor safeguards your furnace against the unsafe burning of fuel, and a dirty flame sensor may cause your furnace to function improperly. Typically, the flame sensor comes in the form of a rod that can be found near the back of the furnace, right in the path of the burner. To clean the sensor, turn off power to the furnace at the breaker box. Then, if possible, remove the sensor from the furnace. Scrub the sensor gently to remove dust and other residues. Finally, reattach the sensor and resume power to the furnace.
The chill of winter can be a scary thought when your furnace needs a repair. When the furnace in your home goes on the fritz, you need it fixed right away to keep your family safe and comfortable. Every BGE HOME technician is licensed in their trade and adheres to a stringent in-house certification program that guarantees their knowledge, affirms their commitment to the customer, and ensures excellence in completing every repair with the highest level of quality. Our technicians average 11 years in the HVAC industry, so you can rest assured that the technician who makes your furnace repair is knowledgeable and experienced.
×