As your air conditioner operates, it is going to suffer some general wear and tear. There is really no way in which to avoid this. However, wear and tear does not have to result in serious problems with your air conditioning system. Just make sure that you schedule professional air conditioning maintenance in Seattle, WA in order to keep your system in great working condition.
We have done furnace services numerous times for last 10+ years. All that this technician did was to vacuum inside the furnace, asked me to turn on and turn off furnace, and said it is working fine. He didn't clean the burners, didn't check heating effectiveness, didn't check / change the filter ... Total rip off. I am calling amazon customer service.

Jeremi came out and serviced our air conditioner, checked our furnace, replaced our filter, set our thermostat and cleaned our alot of cottonwood out or our air conditioner on the side of our house. He was a great technician and did and great job. after he adjusted everything and cleaned out the vents in the air conditioner outside the house was cooler than it was. He is a nice man and very personable. Both my wife and I were very happy and satisfied with his work. the service was done on Thursday, July 21st, 2016
Vredevoogd Heating & Cooling Grand Rapids employs more than 80 people who are proud to work under the Vredevoogd Heating & Cooling banner. Each team member shares our company values for service excellence. All of our employees are intensely screened and background checked so that you have peace of mind when they enter your home. Moreover, our technicians are certified to work in the HVAC industry and provide the level of expertise that our customers expect from Vredevoogd Heating & Cooling. We back our technicians’ work and continue to make training a priority so that all of our techs are familiar with the latest HVAC models and advances. Our customers deserve the best, so the best is what we deliver to each and every job.
CM Heating performed an electric furnace Diagnostic - Upon investigation, I found that the sequencer has failed which is why all heat elements are not being activated (3 out of 5 work). This is the second replacement sequencer needed in less than 5 years of operation, the unit is an old model of air handler and only source of heat. Replacement of sequencer is needed, however, based on age and efficiency recommend upgrade of system.
Edwards Heating & Air continues to look for new ways to improve service.  We hire only NATE-certified, extensively experienced, and dedicated professionals.  We offer a wide range of products, from ductless options to heat pumps, furnaces, air conditioners, and air quality systems, guaranteed to answer the most challenging comfort demands.  To maintain your equipment in peak condition, promoting year after year of uninterrupted performance, we offer preventative service plans that are affordable, convenient, and effective.  If you are ever confronted with a malfunction, the team from Edwards Heating & Air is always available, 24 hours a day, 7 days a week, to provide the skilled assistance you need. Through our relationship with Wells Fargo Financial National Bank, we offer flexible financing options with approved credit to facilitate your investment into superior quality heating and cooling.  Our ongoing dedication to your complete satisfaction is evidenced by our complaint-free, A+ rating by the Better Business Bureau.  At Edwards Heating & Air, we do things right, every time.
Our company’s strength lies in our years of experience performing air conditioning and heating repair in Voorhees, Sewell, Haddonfield, and other towns in and around South Jersey. We also take pride in the high standard we set for the quality of our AC repair and work, and our unfaltering dedication to our customers located in Haddonfield, Sewell, and other parts of Jersey. For three generations we have kept these ideals at the forefront of our operations, allowing us to continue to be one of Southern New Jersey’s leading HVAC Contractors and air conditioner companies.
Vredevoogd Heating & Cooling Grand Rapids employs more than 80 people who are proud to work under the Vredevoogd Heating & Cooling banner. Each team member shares our company values for service excellence. All of our employees are intensely screened and background checked so that you have peace of mind when they enter your home. Moreover, our technicians are certified to work in the HVAC industry and provide the level of expertise that our customers expect from Vredevoogd Heating & Cooling. We back our technicians’ work and continue to make training a priority so that all of our techs are familiar with the latest HVAC models and advances. Our customers deserve the best, so the best is what we deliver to each and every job.
Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
The quality of the air you breathe affects your comfort, health, and productivity.  Whether at home or in the workplace, an ample supply of fresh, clean air is essential to everyday life.  Whatever concerns you may face, Edwards Heating & Air provides proven, cost-effective products to significantly improve Indoor Air Quality.  Our NATE-certified specialists are qualified to analyze your residential or commercial space, make informed recommendations, and implement a strategy specifically targeted at your unique circumstances.  As a Carrier Factory Authorized Dealer, we are extensively trained in leading-edge products that silently and effectively eliminate harmful bacteria, fumes, chemicals, viruses, smoke, and much more.  The installation of a humidifier, ventilator, air filter, or UV lamp will protect the health of your indoor breathing air, maintain a cleaner, more comfortable home, and even reduce energy costs.  Contact the specialists from Edwards Heating & Air for trusted solutions and complete peace of mind.  
The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.

Given the broad price ranges above, it's easy to recognize that the cost of your furnace repair varies drastically based on which parts need attention. As a result, it makes sense to gain a better understanding of the parts that heat your home, and how much they cost to repair. Repairing or replacing your furnace’s blower motor can cost you anywhere between $150 and $450, depending on the extent of the damage. Heat exchanger repair costs can vary greatly, from as little as $100 for a simple fix to as much as $1,200 for a full replacement. Repairing a furnace igniter will only cost you $300 at most, while flame sensor repairs generally fall between $80 to $250. The average cost to repair your Thermostat will range from $108 to $282.
Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.
Has another company told you that your furnace has a cracked heat exchanger?  The heat exchanger is the heart of your furnace. Its failure can result in a dangerous situation for your home and the best solution is usually a new furnace.  Because of these issues, Bonney takes this situation very seriously.  We will offer you proof of the cracked heat exchanger in the form of a picture from our video inspection camera or a report from our exhaust gas analyzer, before we make our recommendation.
×