Locally owned and family operated, M and M, Heating & Cooling, Plumbing & Electrical customizes solutions to perfectly fit your requirements and lifestyle. We specialize in a wide range of services including plumbing, water heating, indoor air quality, and residential and commercial temperature control. Our team of highly trained and certified technicians are fully licensed and insured, adhere to strict service procedures, and meet exacting standards of quality. Call on M and M, Heating & Cooling, Plumbing & Electrical at (720) 443-6119 for dedicated service throughout Longmont, CO & surrounding areas, and have confidence in a rewarding experience and long-term results. With over eighteen years of satisfied customers, we take great pride in a job done right.
When choosing a heating and cooling company, it's important that you find one that employs licensed, highly trained, background-checked, and drug-tested technicians. Considering this person will be in your home, it would be nice if the technician is also well-groomed, honest, polite, informative, and will give you options on how to improve your comfort.
Geothermal Heating and Cooling systems are unmatched in every way. This green alternative to temperature control is three times more efficient than conventional systems. Recognized by the US Environmental Protection Agency as the most environmentally-friendly option available today, installation of a geothermal HVAC system translates into a 50% reduction in heating costs, 30% reduction in cooling costs, and a 65% potential savings on hot water costs.  Sky Heating & Air Conditioning is now the largest WaterFurnace geothermal contractor west of Iowa. Our team of experienced professionals offer conscientious and skilled start-to-finish installation and service.  We specialize in outstanding geothermal HVAC systems, adding value and enjoyment to your home through sustainable solutions to year round temperature control. Contact Sky Heating & Air Conditioning for geothermal heat pump installation in Portland.

The motor belt should be firm, giving no more than ½ inch when pressed. It should also be free of cracks and damage. To remove the belt, you will need a wrench and a replacement belt. Loosen, do not remove, the motor bolts. You only need them loose enough to move the motor and slacken the belt. Remove the belt and inspect it, replacing it with a new one if necessary. Belt: $4.00 to $6.00.
If you’re looking for a professional heating company in Denver with the proper experience to handle your project, our crew has many years of training and experience on most major heating systems available in the Denver area. Our heating company in Denver understands that in some situations, the scope of the damage may put the units beyond repair. In this instance, we can offer you help finding the right energy efficient model that will provide you warmth and savings in your wallet. Heating in Denver can be expensive during the coldest time of year, so choosing the right heating system can give the same amount of heat while at the same time providing big savings when our Denver heater repair technicians help you pick the right system for your home.

Customer would like to have her furnace maintained before winter. She would also like her blower wheel and assembly cleaned. System was operational upon arrival. I checked the components within the unit and found the blower capacitor was out of specifications. It was replaced with new one. Blower assembly was pretty dirty. I cleaned the assembly. Burner assembly was ok, I cleaned flame rod. CO output was nominal. Heat output was also nominal. No other issues at this time.


Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.


Our technicians have experience repairing furnaces and will make sure your home is back to keeping your family cozy in no time. From training and certifications to our reputation for doing the job right time and time again, you can trust that James Heating & A/C, Inc’s furnace repair technicians will have your troubles taken care of and your furnace operating smoothly. Whether it’s emergency furnace repair or service you can schedule a little in advance, our team can give you peace of mind, knowing that your furnace is in good hands. Are you in need of a furnace repair? When performing a repair, it's important to hire professional HVAC contractors.
We install heating equipment from Lennox and can repair all major brands, including Carrier, Trane, York, Bryant, Rheem, and many more. We proudly offer same day service and next day installations. Dealing with a heating emergency? We've got you covered! Our team is prepared to assist you 24 hours a day, 7 days a week to ensure that your home remains comfortable and safe for you and your family members.
In order to make your everyday life easier and more enjoyable, Sky Heating & Air Conditioning specializes in state-of-the-art heating and cooling technology, partnering with Trane, Mitsubishi, and Waterfurnace.  We bring you HVAC solutions that represent the best the industry has to offer, ensuring long-term performance and satisfaction.  Whether you’re looking for the design/build of a new system, replacement, or hoping to cut costs and enhance convenience, we answer with proven products.  Our qualified HVAC technicians help you determine the ideal solution for your exact requirements, and make sure you’re happy with every step of the process.  From ductless HVAC to geothermal heating and cooling systems, we offer a wide selection of options and comprehensive services to answer any type of challenge.  Call on Sky Heating & Air Conditioning and let us exceed your expectations today!
Tyson from Brothers was courteous, efficient and familiar with the system, because he had worked with it before. He arrived early within the time window and was professional, fast and made it possible for me to happily spend my day doing other things rather than devoting all day to the sprinkler turn off procedure and worrying if the job had been done properly.
Denver furnace repair is very common in the winter. Our availability 7 days a week is a major advantage. That is the main reason as to why we are a popular furnace repair company. In general, furnaces tend not to start at all or are cracking out cold air instead of heat. Contact us, your Denver furnace repair company so that we can diagnose the problem and set you up with a preventative maintenance package. Click HERE to learn more about our furnace related services.

The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.
There may come a time when air conditioning repair is not enough. If you find that your air conditioner breaks down irreparably, then you may need to opt for air conditioning replacement service. At Bob’s Heating & Air Conditioning, our Federal Way air conditioning replacement technicians can make certain that you make an informed decision about the status of your AC, whether you have a heat pump or central AC.

As touched on by their name, heat pumps function by transferring heat energy indoors during the winter and outdoors from your home during the summer. They're often attached to air conditioning units, using the surrounding air to transfer energy. However, geothermal heat pumps and water source heat pumps are also available. The cost to repair a heat pump, again, depends on the specific problem. Replacing a faulty thermostat may cost up to $300 including labor, while a worn or damaged defrost control board can set you back up to $600. For more details on your potential repair costs using this heating source, visit our heat pump repair cost guide.


Mechanical air filters trap pollutants by filtering them out of the air as it passes through. Electronic air cleaners pull air in, give the pollutants in that air a static charge, and trap those pollutants on an oppositely charged surface. By working with a qualified professional you can rest assured that you have the right air filtration system in Seattle, WA.
At Sky Heating & Air Conditioning, we understand that HVAC services can really hurt your budget. Many times, you don’t expect to make such large purchases until an emergency arises. We never want you to feel that you cannot afford your comfort and safety. We offer flexible financing options through the Home Project credit card from Wells Fargo, with approved credit. Head over to our financing page to apply, or give us a call for more information!
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.
I have a Bosch condenser dryer that heats up and after 3-5 mins cuts out (no lights/power). After is cools a while, the machine can be restarted and runs a while longer until it shuts down again. This process repeats several times, with each progressive drying cycle being a little longer than the previous until the clothes are eventually dry.I've tested the the thermal-protector for continuity and the NTC-sensor on the heating element appears to be fine (tested for resistance). Could it be a faulty sensor/component on the control board that's getting too hot and cutting out the power? And if so, can it be easily identified/replaced, or would I need to replace the whole control board?Any help would be greatly appreciated!
Vredevoogd Heating & Cooling Grand Rapids values each and every customer. Servicing or installing your HVAC system means establishing a service relationship with each homeowner. We promise to earn your trust with our consummate level of professionalism and expert service. We back our work with the strongest industry guarantees because we value your continued business.
Of the various contractors and HVAC service companies, why should you choose AQS for air conditioning and furnace repair? Our company is a family-owned and operated business that has been in business since 1996. It goes without saying that we are extremely experienced in the installation and repair of heating and cooling units. We are proud of our A+ rating from the BBB, and we have received numerous Super Service Awards from Angie's List, both in recognition of the quality services we provide.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.
When you contract with Vredevoogd Heating & Cooling Grand Rapids MI, you can count on us to make safety our top priority. Your HVAC system is, of course, a major investment and integral to the functioning of your home; however, nothing is as important as the safety of each life within your home. We carefully inspect your system to ensure that it is functioning properly in order to guard against carbon monoxide poisoning or other system emergencies. We take the greatest care when installing your HVAC system, knowing that a perfect installation is the safest installation for your home. We follow our industry’s best practices concerning safety and will happily share our know how with you when it comes to safely maintaining your system between service appointments.  If you ever suspect a problem with your HVAC system, you hear strange noises or smell unpleasant odors, for instance, you can call us night or day, 24/7, to address your heating and cooling emergency. We’ll never leave you in the lurch! We are ready to provide service ASAP to ensure the safe operation of your HVAC system.

For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.

×