Adam V. from Swan Plumbing & Heating of Denver, CO came out and tuned up our furnace and A/C units. He was courteous prompt and professional, but beyond that went out of his way to give us recommendations on things we can do to get the most life and performance out of our existing equipment. When we are ready for upgrades and additional services, Swan will be our first (and only) call.
Whether you are looking for gas furnace service or repair, quality installation of a furnace, heat pump or air conditioner, mini split ductless heat pumps, endless hot water from tankless water heaters, better air quality in your home or just a filter change or duct cleaning, Greenwood Heating is your best choice of Seattle heating contractors and cooling specialists.

So the furnace went out (again). We’re probably not the people you want to be dialing, but in these circumstances, Service Experts Heating & Air Conditioning in North America should be your very first call. You don’t even have to worry how late (or early) it is – our NATE-certified technicians available at all hours, every day of the year. We’ll be there in a jiffy and get the job done fast – so you can get back to your routine and not have to even think about needing another furnace repair anytime soon.
Here at Four Seasons Heating and Air Conditioning, we understand that the toughest aspects of winter weather can sometimes be too much for any furnace. That’s why we offer year-round, same-day furnace maintenance to ensure that your home and family never freeze. With no additional charge for after-hours service, you’ll soon discover that Four Seasons Heating and Air Conditioning is the affordable, expert service your home needs and deserves.
Has another company told you that your furnace has a cracked heat exchanger?  The heat exchanger is the heart of your furnace. Its failure can result in a dangerous situation for your home and the best solution is usually a new furnace.  Because of these issues, Bonney takes this situation very seriously.  We will offer you proof of the cracked heat exchanger in the form of a picture from our video inspection camera or a report from our exhaust gas analyzer, before we make our recommendation.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.
When you need a new air conditioner installation, Seattle furnace repair, or want to schedule routine water heater maintenance, there is one company to call: Bob’s Heating & Air Conditioning. We have years of experience with heating, air conditioning and water heater services, and we can ensure that your home is comfortable throughout the entire year. Contact us today to schedule the high–quality HVAC and water heater services you deserve.
Bryant manufactures and markets gas central furnaces that are available in single and multistage configurations, with some models capable of an AFUE rating of more than 90 percent. Bryant markets units that meet Energy Star requirements and makes others that it claims offer quiet operation. A new line of hybrid heat systems that uses gas and an electric heat pump was recently introduced. The average price of a Bryant central gas furnace is about $2,300 and Bryants are sold through their dealer network.
If you pull out your home’s air filter, hold it up to a light. If you can’t see light coming through it, it’s most likely been a while since your last heating service, and likely time to get a new one. If it’s a simple disposable air filter, just replace it with a like-size new one. It’s also a good idea to write down the date you installed the new filter, so you know how old it is next time it needs to be replaced. Check the filter packaging to see how long the new air filter is supposed to be used.
All of our AC repair technicians and teams at our HVAC and air conditioning company in Gloucester County are extremely knowledgeable, dependable, helpful and just like members of the family. This family atmosphere helps us provide our valued customers in the towns of Haddonfield, Sewell, and all of South Jersey with top-notch service, because everyone here takes great pride in their work.

In December of 2004 Greenwood was sold again to Michael Porter, this time going back to its Puget Sound roots… owned by a local Seattle resident. Michael Porter, a West Seattle resident and a life-long Seattle native. He is committed to complete customer satisfaction and has a mission to be ‘The Most Trusted HVAC Company in the Puget Sound area’. To become the best heating contractor in Seattle and the Eastside he knows he must be able to provide the Highest Quality and most energy efficient Air Conditioning and Heating products on the market. But there is so much more to being the best. Greenwood Heating is also your local expert when it comes to endless hot water systems, they are also your Indoor Air Quality experts with a full product line of air cleaning products.
Having a company take care of all your heating and cooling needs shouldn’t indicate that you’re stuck with any ordinary shop who cuts corners. Heating and cooling has been our excitement since 1967, and it’s apparent in the work we offer to our customers. We’re committed to offering you the very best when it comes to all things HVAC, whether it’s service, maintenance or heating and cooling systems.
Heating your home is an essential part of feeling comfortable while indoors and is also essential for health and safety during a chilly winter evening. When temperatures dip into the 20s and 30s, you need emergency heating repair in Houston. From general repairs like pumps, gas valves, heat exchangers, diverter valves, flow switches and fans, to total heating system replacements and installations, Abacus Plumbing can ensure your home is warm when it needs to be. Don’t be left out in the cold! Call Abacus Plumbing today for a quality, reliable heater repair company in the Houston area.
Your HVAC system is an important appliance with a limited lifetime. Depending on use, with regular maintenance you can expect your furnace and air conditioner to last between 8-18 years before you will need to replace the old one. However, poor maintenance is one of the primary reasons for early replacement HVAC systems ahead of end of average life expectancy.
Thank you Caleb Elliott for servicing our water heater. We are ready for winter! Caleb was very personable and did a thorough job servicing our water heater. We appreciate Reliable's commitment to service and keeping things running for us. Every service person we've had has been top notch. So glad we chose Reliable to take care of us. Continue reading...
Next check and clean the furnace’s flame sensor. The video below shows you how—note that this guy fixes it in about 5 minutes. We would probably use a little bit of emory paper, but he cleans the sensor with a 5-dollar bill. Another video further down the page under the discussion of “If your furnace keeps shutting off after about 5 minutes” shows the same project with a different brand of furnace.

If you own a forced–air distribution system, then you need to ensure that you take care of your ductwork. After all, your central AC or heat pump is only as effective and efficient as the cleanliness and integrity of the ducts that transport your conditioned air. With our air duct cleaning service in Federal Way, WA, your HVAC system is in good hands.
Service Experts Heating and Air Conditioning was founded on the basis of providing customers with the best heating and cooling practices in the industry. Since its inception, Service Experts has been dedicated to community, providing the top of the line HVAC products and services in your area. If you want more information about your local HVAC leaders, call us at 866-397-3787 or set up an appointment with us online.
You'll find we take our job seriously and value highly the trust that is placed in us. To understand why we go so far beyond what others do by investing in the extra training and equipment we believe necessary to protect your home and family properly, take a moment to view our short 30 second video that best explains "why we do it"...and "why it matters."
I had a minor crisis at my home with a backed up sewer drain in the basement and me just home from a freak accident where I broke both arms! Spencer narrowed down the problem and called his coworker who had the equipment to snake my drain and stayed to clean up until the issue was resolved. He was courteous and careful to make sure my carpet didn't get marked up and cleaned up well. I am so grateful for him being willing to go the extra mile to help me out!

Since 1994, Welzig Heating & Air has been providing professional air quality solutions throughout Boulder, Longmont, Louisville, Lafayette, CO & more. We specialize in industry leading products and employ skilled and knowledgeable technicians to do the job right the first time. As a family owned company, we understand how important the quality of your indoor environment can be on your health, comfort, and productivity. When you call the team from Welzig Heating & Air, you’ll enjoy helpful recommendations, convenient appointment times, and rewarding installation service that leaves you feeling refreshed.


2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
Does your water heater make a loud or strange sound during operation? Are you sick and tired of unreasonably high energy bills? Are you out of hot water? Let us take a look at your water heater so that we can take care of any problems that may arise with its operation. Our water heater repair services in Federal Way, WA are thorough and comprehensive.
Trained to quickly and accurately make the diagnosis, our expert troubleshooters possess both the skills and speed that you need. Responding swiftly to your call, one of our technicians will provide you with a handwritten, fair and competitive estimate that details how exactly your system will be repaired. Offering a one-year parts and labor warranty, we restore your heat—and minimize your financial stress.
Bryant has been an industry leader of heating and cooling products for over a century. Innovative Bryant HVAC systems provide dependable solutions to home and commercial comfort and air quality. With everything from heat pumps to gas furnaces and air conditioning systems, Bryant has the products that offer leading-edge technology and precision engineering. Call us today to learn more!

We are committed to providing you with services that are effective and efficient. We do the job right the first time, but more importantly, we won't charge our customer when we didn’t fix it the first time. For almost 30 years, we have been providing our customers with work from industry-certified technicians. Our team has the skill and knowledge to get the job done right the first time out!
If you have an older furnace with a standing pilot light, it’s possible that the pilot light has been extinguished. First, confirm that the light is out. Then, turn the gas valve to the off position and wait five minutes. If there is a reset button on your furnace, turn the valve to the pilot position and hold a flame to the dedicated pilot opening while pushing the button for about 30 seconds. (If the pilot doesn’t light on the first attempt, wait a few minutes and repeat the procedure, this time depressing the reset button for 45-60 seconds.) Once the pilot is lit, turn the gas valve back to the on position. If the pilot light won’t stay lit, it’s possible that there is an issue with the thermocouple or ignition system. Call an HVAC professional for assistance.
Environmental Protection Agency (EPA) has selected Sears Home Services as a 2018 ENERGY STAR Partner of the Year winner for Sustained Excellence — Retailer and Energy Management. This award is reserved for ENERGY STAR partners demonstrating outstanding leadership and exceptional commitment to the environment by providing consumers with products, services and information that help individuals make sustainable purchasing decisions.

At Welzig Heating & Air, we focus on quality.  Recognizing that a cut corner today results in long-term problems and expense, we adhere to strict procedures for service and installation, and recommend only premier products.  While we provide affordable solutions to indoor comfort, we refuse to compromise integrity with subpar equipment, materials, or workmanship.  If you’re looking for residential or commercial heating, cooling, air quality, or water heating services of a higher caliber, Welzig Heating & Air delivers satisfaction across Boulder, CO & Surrounding Areas.  Contact us at 303-678-5576 anytime you need us.  Our dedicated technicians are on-call, ready to handle any challenge, 24 hours a day, 365 days a year.
So the furnace went out (again). We’re probably not the people you want to be dialing, but in these circumstances, Service Experts Heating & Air Conditioning in North America should be your very first call. You don’t even have to worry how late (or early) it is – our NATE-certified technicians available at all hours, every day of the year. We’ll be there in a jiffy and get the job done fast – so you can get back to your routine and not have to even think about needing another furnace repair anytime soon.

Dirty furnace filters are one of the most common causes of a furnace failure. A dirty furnace filter can limit the airflow through your furnace and cause it to overheat. If you suspect a dirty air filter, change the filter, press the reset button (if your furnace has one) and see whether your furnace begins to emit heated air. Change your furnace filters regularly — pros recommend changing them once a month — to ensure that your furnace continues to work properly. Unaddressed, dirty furnace filters can cause extensive, and expensive, damage to your home’s heating system.
To keep your furnace in good working order it’s important to have it regularly cleaned. The national average furnace cleaning cost ranges from $60 to $80, though prices can vary greatly based on where you live in the country and what your furnace maintenance includes. An HVAC company may have different rates for different levels of furnace maintenance. For example,one company may offer general furnace maintenance for $79 and advanced maintenance for $138. Another company may offer a 38-point maintenance check for $89 and a 64-point maintenance check for $178. According to Energy.gov, a standard furnace cleaning and maintenance visit can include:
Over the past twenty years, we have used a number of different heating and cooling companies, none impressed us to use them more than once or twice. The service provided by A-TEMP was so outstanding; they will be our heating and cooling service provider for LIFE! Exceptional all around! It is nice to know why our home has three temperature zones and what we could do to improve it; plus the costs. Also, to understand the importance of regular maintenance-especially as it relates to carbon monoxide emissions. We appreciate the forewarning that our new system would be noisier due to the increased volume in our return system. We feel so blessed to know we do not have carbon monoxide emissions now and the furnace is the right size for our home. We feel like we won a million dollars with our new system!

BGE HOME HVAC repair technicians are thoroughly trained and certified to work on all major brands of heating and air conditioning equipment. When your system breaks down and needs a heating and air conditioning repair, you want to call someone you can trust. Need air conditioning service in the middle of the night? Emergency heating and cooling HVAC service is available 24 hours a day by calling 888-243-4663.
Customer has a 3 year old American Standard gas furnace, she said that her furnace and thermostat were fried and not working. She had an electrician come by and inspect it, but he wasn't able to do anything. Upon investigation, I found that the thermostat has failed due to a power surge that hit the home. I also found that the fuse on the control board was blown and the contactor at the condenser was fried along with wiring. I replaced thermostat, contactor, and fuse/wiring and tested all modes of operation. All components are within manufacturers specifications and system fully operational. Recommend annual maintenance and power surge protector for either home or equipment.
Efficient operation is a function of regular heating system maintenance. When a heating system malfunctions, any one of its three components – heat/cold source, distribution system, or the thermostat  – can be causing the problem. Our technicians can easily detect an impending issue before you have to replace a heating unit or spend a lot of money on parts and labor.

This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
×