Drilon and Jeremy came out to the house for snaking the sewage line and performing an AC tune up. They were very informative, kind, respectful and professional. Drilon went above and beyond by giving me a whole walk through on our furnace, AC unit and water heater and giving suggestions and prioritizing what he thought would be the most important and safe for our new house right now. They were not pushy with their sales tactics and I will definitely be using them when we are ready to replace our features.
As the largest heating company in the Northwest, Washington Energy Services has fixed thousands of heating systems. We service most major brands of heating equipment, including York, Bryant, Carrier, Lennox, Coleman and Rheem. Our NATE certified, factory trained service technicians are standing by for furnace service, and also heat pump and air conditioning repair. Home owners from Sea-Tac to Lynnwood trust Washington Energy Services for furnace service and repair. Schedule your service today!

Gas is currently the most common heating fuel and most new central-heating systems use gas. How efficiently a furnace converts gas into heating energy is reflected in its annual fuel-utilization-efficiency (AFUE) rating, which is measured as a percentage. The higher the number, the more heat the furnace can wring from each therm of gas. Since efficient furnaces generate fewer emissions, environmental considerations might also influence your decision.


Next check and clean the furnace’s flame sensor. The video below shows you how—note that this guy fixes it in about 5 minutes. We would probably use a little bit of emory paper, but he cleans the sensor with a 5-dollar bill. Another video further down the page under the discussion of “If your furnace keeps shutting off after about 5 minutes” shows the same project with a different brand of furnace.

You'll find we take our job seriously and value highly the trust that is placed in us. To understand why we go so far beyond what others do by investing in the extra training and equipment we believe necessary to protect your home and family properly, take a moment to view our short 30 second video that best explains "why we do it"...and "why it matters." 

Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.
Steel T Heating & Air Conditioning is uniquely qualified to recommend and install the industry’s most recognized heating and cooling systems, from central air conditioners and furnaces, to heat pumps, ductless units, and air quality accessories. We offer a range of innovative products to improve the health, comfort, and convenience of your everyday life. Plus, we’ll stand with you throughout the entire product life, offering skilled installation and replacement, seasonal maintenance, and 24 hour repair to maximize the return on your investment. Targeting cost-savings, energy efficiency, reliability, and safety, Steel T Heating & Air Conditioning is your single solution for temperature control. Contact us to day for heating and air conditioning services in Littleton, Lakewood, Centennial, Highlands Ranch & Englewood, CO.
CM Heating performed an electric furnace Diagnostic - Upon investigation, I found that the sequencer has failed which is why all heat elements are not being activated (3 out of 5 work). This is the second replacement sequencer needed in less than 5 years of operation, the unit is an old model of air handler and only source of heat. Replacement of sequencer is needed, however, based on age and efficiency recommend upgrade of system.
Seattle furnaces can run nine months of the year. Based on the average temperatures in our area, if you compared running your furnace to a car it would get the equivalent of 1.8 million miles over its expected lifespan of 15 years. Your heating system will work hard for you, but like your car, doing routine and regular maintenance will keep it running smoothly, avoid problems, and keep your warranty intact.

Our Denver heating company understands that in our small part of the country, it is important that your heating system is maintained throughout the year to ensure it runs efficiently when you need it the most. Our specialists in heater repair in Denver recommend that your heating system is maintained at least once a year to spot potential problems before they have the chance to worsen and cause your system to fail at the worst possible time. At Brothers Plumbing, Heating, and Electric, our professionals are committed to diagnosing any problem your heating system may suffer while it still remains a minor repair.


Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.
As a technical industry, the heating and cooling field is associated with annual advances. New energies make our industry an exciting place to work. Our team thrives on keeping up to date with all changes in the HVAC field. We are here to share our knowledge with each customer. When you are ready to update your HVAC system, we can help you select the ideal system for your home.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
×