Getting the most from your air conditioner means more than just adjusting the temperature so often. While today’s air conditioners are increasingly reliable and they often last for years upon years, they must be routinely taken care of by a professional air conditioning maintenance technician if they are to function as intended. With our air conditioning maintenance in Federal Way, WA, your system is in good hands.

The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.


Furthermore, routine water heater maintenance also ensures that your system works as it should. When dust and other sediment build up within the tank or on other components, they can present serious problems for energy efficiency and hot water capacity. Let our Federal Way water heater maintenance specialists keep your water heater in good working order.
We tend to have fairly moderate winters in Federal Way, WA, and that means a heat pump works well down here. A heat pump works much like a central air conditioner in that it circulates a refrigerant that transfers thermal energy from one place to another. But heat pumps not only cool your home during the summer, but also heat your home during the winter.
While repair is often the preferred choice, problems like a consistent repeating complication or extra-costly furnace repair parts might start leading you in a different direction. Remember that repair is only the preferred option when the cost of seeking it makes sense! If you’re shelling out for repair every single year, then it might be time to talk to your heating contractor about furnace replacement.

The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.
©2018 By Horizon Services, LLC. All Rights Reserved. DE License # PL0000726, HL0000299. Contractor Reg. # PA017876, PA057742. NJ Plumbing Lic. # PL36BI01232300 - David Geiger HIC reg. # 13VH05117300, NJ Master HVACR contractor Lic. # 19HC00193700. MD Master HVACR contractor Lic. # 47186, MD Master Plumber/Gas Fitter Lic. # 63739 – David Geiger. EL.LIC./B.P. #34EI01207700.
Your heating, cooling, and air quality systems are a significant investment, and are expected to answer high demand, day after day, year after year.  To enjoy the greatest benefit from your equipment, let the professionals from Edwards Heating & Air handle the essential upkeep.  Through conscientious, seasonal maintenance, we effectively restore operational sound and efficiency levels, improve air quality, eliminate the majority of repairs, and extend service life.  The key to safe and uninterrupted performance, lower overall costs, and superior temperature control is through proactive measures.  The NATE-certified technicians from Edwards Heating & Air complete a lengthy task list that is specifically targeted at the optimization of your system.  Not only will your HVAC system be ready and able to handle volatile weather conditions, but it will operate safely.  Comprehensive service from Edwards Heating & Air is your best protection against health concerns, property damage, system failure, and elevated cost of ownership.  Contact Edwards Heating & Air, and we'll set up a maintenance plan that is affordable, convenient, rewarding, and works perfectly for you.
In this video I show you a few things to look for to fix your furnace. It's expensive to call a repair man and most of the time is not needed. I am not an expert, just someone trying to share my experience with you to save some money. Always turn your power to your furnace off before tampering with things. This would be a good video to start with because I try to show a general idea of how a furnace works. When all else fails, you have to call an expert, but first try the steps in this video.
Superior AC & Heat inspected my furnace on Monday and determine that I needed to replace the furnace. Since I was also desiring to add AC to my home, I decided to bundled both projects and get a new furnace and AC Unit together. The team arrive at my home Wednesday morning at 7:45 am; the new furnace was installed by 1:00 pm and they completed the AC Unit, tested it and cleaned up by 4:30 pm. Great work; I highly recommend them.
Your HVAC system is an important appliance with a limited lifetime. Depending on use, with regular maintenance you can expect your furnace and air conditioner to last between 8-18 years before you will need to replace the old one. However, poor maintenance is one of the primary reasons for early replacement HVAC systems ahead of end of average life expectancy.
By combining immediate results with sustainable performance, we protect the value of your investment.  We provide skilled installation, maintenance, and repair of gas furnaces, heat pumps, dual fuel systems, boilers, air conditioners, air quality products, traditional and tankless water heaters, and advanced duct cleaning services.  Welzig Heating & Air is the right choice for  the comfort, safety, and health of homes or offices across Boulder, Longmont, Louisville, Lafayette, CO & more.
Lennox is another leading manufacturer and marketer of gas central furnaces. Lennox central furnaces are available in single and multistage configurations, with some models capable of an AFUE rating of more than 90 percent. Lennox markets units that meet Energy Star requirements and makes others that it claims offer quiet operation. The average price of a Lennox central gas furnace is about $2,500 and Lennoxes are sold through their dealer network.
Our goal is to make you more comfortable in your home. When your furnace, central air conditioner, heat pump or boiler stops working and you need service, call the professionals at BGE HOME. Heating and cooling system breakdowns occur at the most inconvenient times, so rely on our certified, skilled technicians to make the repair quickly and correctly the first time.

Relax—ABC Plumbing, Heating, Cooling & Electric is here for you when you need us most! Our highly trained, background-checked technicians perform heating and air conditioning repairs quickly and efficiently to keep your family warm and cozy all winter long. With over 65 years of experience, you can trust that we’ll fix your furnace correctly the first time.
Two nights ago our smoke alarm went off during the night...after a frantic search through the house we traced the source of the smoke to the furnace.  After reading reviews about Affordable Furnace Repair we decided to give them a try...and we are SO GLAD WE DID!  Within 10 minutes of leaving a message I received a call back and was scheduled the next day.  The source of the problem was immediately identified and promptly fixed....a previous repair had messed up some wiring as well which was also fixed and now we are so glad to be back to 100%.  Can't say enough about the professionalism, responsiveness and service.  Highly recommend.

For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.

Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
Whether you’re satisfied with your water heater’s performance or not, you would do well to take advantage of our professional water heater services in Federal Way, WA. Water heaters are sturdy and reliable when professionally installed and serviced, but there may come a time when you need to call on the Federal Way water heater experts at Bob’s Heating & Air Conditioning for water heater repairs.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
A-TEMP has been serving the residential heating and air conditioning needs of greater Portland-area homeowners for almost 50 years. We are all about home comfort, just right. So we know how to keep you comfortable all year-round with responsive service, quality products, and well-trained, certified technicians. We offer efficient, best-of-class choices in furnaces, heat pumps, central air conditioning, duct cleaning, service contracts, and more.

The motor belt should be firm, giving no more than ½ inch when pressed. It should also be free of cracks and damage. To remove the belt, you will need a wrench and a replacement belt. Loosen, do not remove, the motor bolts. You only need them loose enough to move the motor and slacken the belt. Remove the belt and inspect it, replacing it with a new one if necessary. Belt: $4.00 to $6.00.
When you establish routine visits with Vredevoogd Heating & Cooling Grand Rapids MI, you can enhance the longevity of your HVAC system with our custom care. Our technicians are skilled at performing comprehensive inspections. We routinely spot small issues before they can turn into major repairs. By optimally maintaining your system, we can extend its life and ensure that it reliably meets your household’s heating and cooling needs. You can also join our Comfort Club! You can schedule routine appointments to service your system before the hot and cold seasons. If you discover a problem afterward, call us to provide you with immediate service. We can troubleshoot the problem in no time. We’ll give you an upfront estimate concerning cost, parts, and labor. There’s no guessing when it comes to our service and costs. Our techs will provide you with everything you need to know about their service from beginning to end of the job. We even have Financing Available.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
You cannot afford to gamble with your comfort. If your air conditioner is not expertly installed, routinely maintained and professionally repaired, you are really putting your comfort at risk. Our Seattle, WA air conditioning experts have the experience and training they need to ensure that your air conditioner is ready for action when temperatures rise.
On average, furnace repair costs $287 nationally, with some homeowners spending as little as $60 while others paying $900 for furnace maintenance. Repairs to an electric furnace can run you $300 or less, while gas furnace repairs can be more complex and range from $375 to $1,200, depending on the what needs service. Most homeowners spend between $131 and $453 to fix their furnace. Here is what you need to know, along with the various factors that could affect the price of your furnace repair.
In addition to our gas and electric furnace installation, our Federal Way furnace technicians also make certain that your existing furnace works well for years to come with our furnace repair and maintenance services. Whether your furnace has broken down and no longer functions effectively, or you want to stave off problems by having it routinely maintained, we can help.
American Standard manufactures and markets central furnaces that are available in single and multistage configurations, with some models capable of an AFUE rating of more than 90 percent. American Standard markets units that meet Energy Star requirements and makes others that it claims offer quiet operation. The average price of an American Standard central gas furnace is about $3,000 and American Standards are sold through their dealer network.
When you need a new air conditioner installation, Seattle furnace repair, or want to schedule routine water heater maintenance, there is one company to call: Bob’s Heating & Air Conditioning. We have years of experience with heating, air conditioning and water heater services, and we can ensure that your home is comfortable throughout the entire year. Contact us today to schedule the high–quality HVAC and water heater services you deserve.

Zach came early, which I very much appreciated, and got the job done quickly. He was unfailingly polite and took care with putting on the booties and keeping my carpet clean. He managed to get the sprinkler system turned off even though I was quite uninformed about it and could help very little beyond pointing to where things were. I am always happy to have Brothers people come out to do my plumbing, heating, & electric services.
Simply put, we put ourselves into our customers shoes and understand that these assurances do more than provide financial protection- they provide peace of mind. Our success is completely dependent on the satisfaction of our customers, so we're willing to do whatever it takes to complete the job to your satisfaction and show you why we're the most trusted when it comes to Plumbing, Heating, Air Conditioning & HVAC in Denver, Colorado!
Drilon and Jeremy came out to the house for snaking the sewage line and performing an AC tune up. They were very informative, kind, respectful and professional. Drilon went above and beyond by giving me a whole walk through on our furnace, AC unit and water heater and giving suggestions and prioritizing what he thought would be the most important and safe for our new house right now. They were not pushy with their sales tactics and I will definitely be using them when we are ready to replace our features.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.
As a Bryant Factory Authorized Dealer, Welzig Heating & Air consistently performs to strenuous standards of technical competence, business ethics, and customer approval.  Our team is NATE-certified, factory trained and regularly updated in progressive technology.  Equipped with leading edge equipment, tools, and a full inventory of genuine manufacturer’s replacement parts, we properly size and install new systems, accurately diagnose existing systems, and resolve the majority of issues right then and there.

Furnace replacement in Denver is necessary if your furnace is broken beyond repair or if it is more than 15 years old. Old furnaces are very inefficient (they use more power and gas than newer ones) and they can even be very hazardous to your health and home. Furnaces are controlled fires, and when the control systems for said fires are out of date or malfunctioning, the safety and wellbeing of your home are in jeopardy. So if you have an old or malfunctioning heater, then give our furnace replacement company a call today.
×